Få besked, når der er ændringer til dette udbud Gem dette udbud under "Mine udbud"

Lot K07 - Cooling of district heating, and heat treatment system

DIN Forsyning Varme A/S in Esbjerg, Denmark is in the process of replacing the heat delivered from the existing coal fired power station (ESV3) which is going out of operation 2023.

DIN Forsyning Varme A/S has decided to establish new base load production capacity to replace the heat previously purchased from Ørsted A/S with new heat production facilities to be located in harbour area close to the existing peak load plant City Centralen and existing heat accumulator tank and distribution pumps.

There will be established 60MW wood chips fired heating boiler, 50MW heat pump and 40MW of electrical boiler.

The Contract Agreement is based on Green FIDIC SHORT FORM of Contract First Edition 1999.

DIN Forsyning Varme A/S intends to enter the Contract with one Contractor for the delivery of cooling of district heating, and heat treatment system.

The Tender consists of a complete heat exchanger system, which will provide cooling of district heating water from approximately 33 degrees Celsius to two degrees above sea water temper-ature. The Heat exchanger system will also provide heat treatment by heating recipient water from approximately 26 degrees Celsius to 40 degrees Celsius by using the hot district heating water with a temperature ranging from 78 to 90 degrees Celsius.

Included in the delivery, the Contractor must take the full responsibility of the project and cal-culations, to ensure the best quality possible in all aspects of the project.

The requirements for the heat exchanger system is described in more detail in 2.0 Employer's Technical Requirements and its sub-schedules.

Åbn udbudsdetaljer (gældende version 15-04-2021) Luk udbudsdetaljer (gældende version 15-04-2021)
Titel Lot K07 - Cooling of district heating, and heat treatment system
Dokumenttype Udbud af bygge- og anlægsopgaver
Opgavebeskrivelse DIN Forsyning Varme A/S in Esbjerg, Denmark is in the process of replacing the heat delivered from the existing coal fired power station (ESV3) which is going out of operation 2023.

DIN Forsyning Varme A/S has decided to establish new base load production capacity to replace the heat previously purchased from Ørsted A/S with new heat production facilities to be located in harbour area close to the existing peak load plant City Centralen and existing heat accumulator tank and distribution pumps.

There will be established 60MW wood chips fired heating boiler, 50MW heat pump and 40MW of electrical boiler.

The Contract Agreement is based on Green FIDIC SHORT FORM of Contract First Edition 1999.

DIN Forsyning Varme A/S intends to enter the Contract with one Contractor for the delivery of cooling of district heating, and heat treatment system.

The Tender consists of a complete heat exchanger system, which will provide cooling of district heating water from approximately 33 degrees Celsius to two degrees above sea water temper-ature. The Heat exchanger system will also provide heat treatment by heating recipient water from approximately 26 degrees Celsius to 40 degrees Celsius by using the hot district heating water with a temperature ranging from 78 to 90 degrees Celsius.

Included in the delivery, the Contractor must take the full responsibility of the project and cal-culations, to ensure the best quality possible in all aspects of the project.

The requirements for the heat exchanger system is described in more detail in 2.0 Employer's Technical Requirements and its sub-schedules.
Annonceret 15-04-2021 kl. 00.00
Deadline 25-05-2021 kl. 10.00
Udbudstype Udbud under tærskelværdierne
Opgavetype Bygge- og anlægsopgaver
Tildelingskriterier Bedste forhold mellem pris og kvalitet
Uddybning af tildelingskriterier Economy (30%), Technical solution (50%), Project solution (20%)
Link til udbudsmateriale http://eu.eu-supply.com/ctm/Supplier/PublicPurchase/298788
Ordregiver DIN Forsyning Varme A/S
Udvælgelseskriterier ‘Solvency Ratio’ for each of the last three (3) closed financial years at the time of the initial tender deadline. ‘Solvency ratio’ must be calculated/determined in accordance with the Danish Financial Statements Act:
‘Solvency ratio’ = ‘Shareholder’s equity’/ Total assets * 100
It is a minimum requirement that the ‘Solvency Ratio’ amounts to minimum 20 percent for each of the last three (3) closed financial years.

The Tenderer must provide minimum three (3) and up to five (5) references which are delivered, and the Tenderer finds most comparable with this invitation to tender, see section 1.4.
If more references are provided, DIN Forsyning Varme A/S will only assess the five (5) latest references. Latest references mean delivered references. If more references are provided, DIN Forsyning Varme A/S will (where relevant) assess the references with the latest commencement date.
The references must have been delivered within the last five (5) years calculated from the date of expiry of the deadline for initial tender. DIN Forsyning Varme A/S will disregard references concluded more than five (5) years before the deadline for initial tender.
The references must contain the following:
1. Description: Description of the reference(s) with focus on the elements which make the reference comparable to this tender, and compliant with the minimum requirements, see the last bullet. The description may also contain information about the period(s) in which the assignment has been performed (start and conclusion dates).
2. Amount: The value of the assignment(s) in DKK, i.e. the amount paid by the customer for the performance of the assignment(s).
3. Date: Date for start-up (commencement date) and date for completion (conclusion date) of the most recent assignment listed under ‘Description’. For references which have not yet been concluded, the field ‘conclusion date’ is left blank/empty.
4. Recipients: Customer name incl. contact person and contact person’s telephone number.

Minimum requirement: It is a minimum requirement, that the Tenderer provide minimum three (3) comparable references which must have been delivered within the last five (5) years calculated from the date of expiry of the deadline for initial tender.
The minimum requirement can be met by the three (3) references containing the above tasks or by a combination of references from several customers, though maximum 5, as long as the references together prove that each of the mentioned tasks has been performed for at least three (3) recipients.

The Contracting Authority understands the following with comparable references:
The reference must include preassembled units containing pumps and plate heat exchanger assemblies including valves and interconnecting piping.
Adresse Ulvsundvej 1
6715
Esbjerg N
CPV kode 42500000-1 - Køle- og ventilationsudstyr
42510000-4 - Varmevekslere, udstyr til luftkonditionering og køling, apparater til filtrering
Udbudsform Offentlig licitation
Kontaktperson Line Sørensen
Kontakt E-mail: kontakt@tohv.dk
Telefon: +45 53383697

Deadline

25-05-2021 kl. 10.00
(-1066 dage og -12 timer tilbage)

Udbudstype Udbud under tærskelværdierne
Opgavetype Bygge- og anlægsopgaver
Tildelingskriterier Bedste forhold mellem pris og kvalitet
Link til udbudsmateriale http://eu.eu-supply.com/ctm/Supplier/PublicPurchase/298788
Ordregiver DIN Forsyning Varme A/S
Adresse Ulvsundvej 1
6715
Esbjerg N
CPV kode 42500000-1 - Køle- og ventilationsudstyr
42510000-4 - Varmevekslere, udstyr til luftkonditionering og køling, apparater til filtrering
Udbudsform Offentlig licitation
SMV venligt
Kontaktperson Line Sørensen
Kontakt E-mail: kontakt@tohv.dk Telefon: +45 53383697